Accessories
Showing 121–144 of 167 results
-
Accessories
Pyle PP444 Ultra compact Phono Turntable Pre-Amp
This electronic preamplifier stands up to the test and will provide you with serious sound performance. The PP444 is perfect for bringing your studio equipment’s phono-level output to a more suitable line-level output. It’ll take your audio signal, amplify its strength and prepare it for further processing by your receiver or amplifier. Preamps technically provide voltage gain to your desired equipment and are key to assisting the signal source, whether it’s a turntable, musical instrument or microphone. The ultra-low noise audio conditioning circuitry allows the preamp to boost audio to levels that are more manageable for various types of audio equipment. You’ll find it easier to adjust the recording level volumes of different sources from microphones and instruments alike. You should position your preamp close to the source to reduce unwanted noise and interference. Preamps can sometimes come built into the stereo equipment, but if that’s not the case, the PP444 is an easy install, wise choice and great addition to any musician or producer. Take your sounds and audio production skills to the next level with the PP444 Preamplifier.
(0 reviews)$ 34.95 Add to cart -
Accessories
Pyle PP555 Ultra compact Phono Turntable Pre-Amp
Connect this Ultra Compact Phono Turntable Pre-Amplifier to your turntable and converts your phono signal to a line level signal-basically connects to turntable output to bring phono level up to line level. Load Impedance: 10K Ohms-Reference Voltage: 1V d State-of-the-art phono preamp to accommodate magnetic pickups. Ultra low-noise audio operational amplifiers offer outstanding sound and performance. Comes with 9 Volt battery compartment or a DC Power Supply for your convenience. Another Great Feature of the PP555 is that it has a 9 Volt battery compartment so if you don’t need extra wires and another Power outlet, which makes this device portable and easy to transport. Voltage is 110V.
(0 reviews)$ 39.95 Add to cart -
Accessories
Pyle PP999 Phono Turntable Pre-Amp
Connects to Turntable Output to ing Phono Level Up to Line Level12V DC Adaptor Included Load Impedance: 10K Ohms Reference Voltage: 1V Input Sensitivity / Impedance/PHONO 3 mV / 50K Ohms T.H.D. : 0.08 for 1 KHz 3 mV Input Output Level;2V S/N Ratio (with A-WTD);70 dB Frequency Response:20 Hz ~ 20 KHz ±2dB Dimensions (WHD):3.54″x2.13″ x1.02″ Weight : 0.88 Lbs Features Connects to Turntable Output to Bring Phono Level Up to Line Level – 12V DC 110V Adaptor Included Load Impedance: 10K Ohms – Reference Voltage: 1V d Input Sensitivity/Impedance/PHONO 3 mV / 50K Ohms – T.H.D: 0.08 for 1 KHz 3 mV Input – Output Level: 2V S/N Ratio (A-WTD): 70 dB – Frequency Response: 20 Hz ~ 20 KHz ±2dB Dimensions: (W)3.54″x (H)2.13″ x (D)1.02″ – Weight: 0.88 Lbs Connects to turntable Input Sensitivity: 3mV at 50K Ohms (phono) Output: 2V max (P-P) at 10K Ohms Includes power adapter 12V DC THD: 0.08% @ 1KHz and 3mV Input | S/N Ratio: 70dB | Frequency Response: 20Hz to 20KHz @ 2dB
(0 reviews)$ 34.95 Add to cart -
Accessories
Phono Turntable Preamp Preamplifier PRE600
This is a Philmore Phono Pre-Amplifier model PHIPRE600. This stereo/phono pre-amplifier will allow you to replace a crystal or ceramic stereo cartridge with a better quality magnetic stereo cartridge while using the original stereo amplifier supplied with your turntable. The use of this pre-amplifier in conjunction with a magnetic cartridge will give you CD quality sound out of your vintage turntable. This pre-amplifier will allow you to take phono signals to line-level. Use this to amplify and interface with mixers, main or monitor systems, audio workstations or sound cards. Uses standard RCA-RCA dual phono cables (not included) with easy in/out plug-ins and works with all magnetic cartridges. This pre-amplifier allows the use of turntables on newer equipment not having a discrete “Phono” input. With this device you can plug into newer equipment using their AUX, DVD, TAPE or CD line level inputs. Features: Convert Phono signal to line level Works with turntables using a magnetic cartridge Good for transferring your old LPs to digital media storage Frequency response: 30-20K Impedance: 50K Ohms Gain: 50X (in+5V out) Max Output: 1.8V Max input: 30mV S/N Ratio: Over 60dB Power requirements 117VAC, 50/60 Hz, 0.1 Watt
(0 reviews)$ 31.95 Add to cart -
Accessories
Turntable flexible very thin wires to rewire any tonearm. About 30 cm length. Set of 4
Replacement four conductor ( Stereo). Tone Arm Wires. Use to replace leads to mono or stereo ceramic cartridges or stereo magnetic types. Solder clips will fit either type or may be cut off for SME style arm. Color Coded, 11.7 inches in length.
(0 reviews)$ 14.95 Add to cart -
Accessories
Turntable Cartridge 4 Piece Connector High-End Lead Wires Set Silver Twisted
Turntable Cartridge 4 Piece Connector High-End Lead Wires Set with Gold connector. twisted. Pack in PP box with foam inlay Mount on cartridge according to the color of shrink tubing: BLUE = LG (left ground) GREEN = RG (right ground) WHITE = L (left positive) RED = R (right positive) Specifications of High-End Lead Wires Sets Cable -Conductor: 7N Copper (OFC), 7-strands, Dia. 0.16mm, silver -Insulation Thickness: 0.41mm -Overall Dia.: 1.32mm -Conductor Resistance at 120 degree centigrade: 42.60Ohm/Kft Connector plug -7N Copper (OFC), AS-06 SILVER connectors, White Cable
(0 reviews)$ 16.95 Add to cart -
Accessories
Turntable Cartridge 4 Piece Connector High-End Lead Wires Set Gold
Turntable Cartridge 4 Piece Connector High-End Lead Wires Set with Gold connector. not twisted. Pack in PP box with foam inlay Mount on cartridge according to the color of shrink tubing: BLUE = LG (left ground) GREEN = RG (right ground) WHITE = L (left positive) RED = R (right positive) Specifications of High-End Lead Wires Sets Cable -Conductor: 7N Copper (OFC), 7-strands, Dia. 0.16mm, silver -Insulation Thickness: 0.41mm -Overall Dia.: 1.32mm -Conductor Resistance at 120 degree centigrade: 42.60Ohm/Kft Connector plug -7N Copper (OFC), GOLD connectors, Transparent Cable
(0 reviews)$ 14.95 Add to cart -
Accessories
Lead Wires for Headshell and cartridge with silver connectors
Phonograph headshell, cartridge lead wires silver connectors set
(0 reviews)$ 9.95 Add to cart -
Accessories
Lead Wires for Headshell and cartridge with silver OFC connectors
Phonograph headshell, cartridge lead wires silver connectors set with lugs
(0 reviews)$ 11.95 Add to cart -
Accessories
Lead Wires for Headshell and cartridge with gold OFC connectors
Phonograph headshell, cartridge lead wires gold connectors set with lugs
(0 reviews)$ 11.95 Add to cart -
Accessories
Audio Technica Vinyl disc Stabilizer for turntable
The AT618a disc stabilizer fits over the turntable spindle to hold records firmly in place, reducing resonance and improving sound quality. The stabilizer is constructed of machined brass with a protective rubber cover. WEIGHT: 600 Grams
(0 reviews)$ 59.95 Add to cart -
Accessories
Vinyl disc Stabilizer in Black Stainless for Turntable
WEIGHT: 760 Grams
MATERIAL: STAINLESS STEEL
LOWER DIAMETER: 70 mm
HIGHER DIAMETER: 28 mm
HEIGHT: 20 mm(0 reviews)$ 54.95 Add to cart -
Accessories
Vinyl disc Stabilizer in Stainless for Turntable
WEIGHT: 760 Grams
MATERIAL: STAINLESS STEEL
LOWER DIAMETER: 70 mm
HIGHER DIAMETER: 28 mm
HEIGHT: 20 mm(0 reviews)$ 54.95 Add to cart -
Accessories
Vinyl disc Stabilizer in Stainless for Turntable
WEIGHT: 465 Grams
MATERIAL: STAINLESS STEEL
LOWER DIAMETER: 70 mm
HIGHER DIAMETER: 57 mm
HEIGHT: 22 mm(0 reviews)$ 46.95 Add to cart -
Accessories
Level Gauge for Turntable Headshell Tonearm Cartridge Spirit Level 108gm with Stroboscope
Bubble shows turntable level at a glance to within 1 degree of accuracy, and test turntable platter speed Easy to use Tests 33-1/3 rpm, 45 rpm, and 78 rpm speeds Works on 50 Hz and 60 Hz diagram.
Turntable Spirit Level Gauge
Diameter 68mm
Height 25mm
Center Hole Diameter 7.5mm
Weight 108grams(0 reviews)$ 21.95 Add to cart -
Accessories
Level Gauge for Turntable Headshell Tonearm Cartridge Spirit Level 108gm
This Turntable Tonearm Spirit Level for Phono / Headshell is compact and lightweight, and is just 68mm in diameter and 25mm in height. Weighs a mere 108 Grams This Spirit Level is placed on the headshell whilst tracking. Spirit Level For Turntables And Other Hi Fi Equipment Where Being Level is Critical to the Sound Quality And Playback Enhancement
(0 reviews)$ 19.95 Add to cart -
Accessories
Level Gauge for Turntable Headshell Tonearm Cartridge Spirit Level 6gm
This Turntable Tonearm Spirit Level for Phono / Headshell is compact and lightweight, and is just 18mm in diameter and 8mm in height. Weighs a mere 6 Grams This Spirit Level is placed on the headshell whilst tracking. Spirit Level For Turntables And Other Hi Fi Equipment Where Being Level is Critical to the Sound Quality And Playback Enhancement
(0 reviews)$ 9.95 Add to cart -
Accessories
Turntable Cartridge Screw set
10 PIECE STAINLESS STEEL TURNTABLE CARTRIDGE MOUNTING HARDWARE SET:
2 x 10mm screws,
2 x 14mm screws,
2 x 18mm screw,
2 x washers,
2 x nuts.(0 reviews)$ 9.95 Add to cart -
Accessories
Universal Turntable Headshell 4 Pin Gold Plated Connector
High quality standard 1/2′ SME type, 4 pin, gold plated turntable connector
Fits most turntables with S shaped tonearm
Made of high quality copper(0 reviews)$ 14.95 Add to cart -
Accessories
Turntable HeadShell Straight Tonearm & Gold Plated Leads
Universal Headshell for Straight Tonearm Turntable with Gold Plated Leads
(0 reviews)$ 24.95 Add to cart -
Accessories
Turntable High Quality HeadShell – Black
Headshell is CNC high precision machined from a single block of aircraft grade aluminum, Lightness and durability high quality aluminum
Black anodized aluminium, so it is a durable treatment that resists scratching and marring
Two lengthened long ( 16mm ) cartridge mount hole, much longer adjusting range than anyother headshell, fit almost all tonearms and cartridges
The connector fit most turntables with the S-Shaped, straight or SME type 4 pin connection tonearm with a standard H-4 Bayonet Mount. The S-shape H-4 type tonearm is the most commonly used tonearm system by turntable manufacturers like National, Panasonic, Technics, Sony, Telefunken, Denon, Sansui, Reloop, Pioneer, SME, DYNAMIC SPEAKER, Schneider, UNITRA etc., just to name a few. The connector dimensions are 8 mm diameter x 12 mm length.
All 4 pins on headshells are 24K gold plated. Comes with nuts and screw(0 reviews)$ 29.95 Read more -
Accessories
Turntable High Quality HeadShell – Stainless
You will receive a top quality turntable headshell that is ready to plug into most S-shaped or straight tonearms. You can be up and spinning in moments. If you have an empty round socket at the end of your tonearm this headshell will fit. It will just plug right into the round tonearm socket as you rotate the locking collar. Size : 8 mm diameter x 12 mm length Plated 4-pin contacts Four colour-coded OFC (oxygen free copper) soft leadwire with gold plated terminal Every terminal inside a color sleeve
(0 reviews)$ 21.95 Add to cart -
Accessories
Turntable HeadShell – Brown
You will receive a top quality turntable headshell that is ready to plug into most S-shaped or straight tonearms. You can be up and spinning in moments. If you have an empty round socket at the end of your tonearm this headshell will fit. It will just plug right into the round tonearm socket as you rotate the locking collar. Size : 8 mm diameter x 12 mm length Plated 4-pin contacts Four colour-coded OFC (oxygen free copper) soft leadwire with gold plated terminal Every terminal inside a color sleeve
(0 reviews)$ 21.95 Add to cart