Phonograph headshell, cartridge lead wires silver connectors set with lugs
SC5 Stylus Cleaner Protect and preserve your valuable stylus with our new SC-5 Stylus Cleaner. Each bottle comes with an applicator to apply a small amount of fluid to the stylus brush. Each kit includes 15 ml bottle with applicator and 1 high quality stylus brush. NOTE: Always brush from back to front! Start behind the stylus and pull forward
The AT618a disc stabilizer fits over the turntable spindle to hold records firmly in place, reducing resonance and improving sound quality. The stabilizer is constructed of machined brass with a protective rubber cover. WEIGHT: 600 Grams
Signal cables optimised for use with turntables. Highly flexible with low capacitance and perfect shield. These cables were developed to have low colouration and are handmade in Europe. “State-of-the-Art” components for leads, dielectric and plugs were chosen after intense listening tests. Specific lengths were chosen because of their significant advantages when carrying audio signals. Three quality levels are available (SI / CC / C).
New Highest quality turntable belt, 27.3″/69,34 cm Inside Circumference x 0.200″/ 0,50 cm Wide x 0.024″/ 0,060 Thick Turntable Belt
New Highest quality turntable belt, 29.5″ Inside Circumference x 0.196″ Wide x 0.023 Thick Turntable Belt
This is a brand new generic replacement flat rubber belt.- manufactured to meet or exceed the Original Equipment Manufacturers specifications. .046 Inch / 1.2mm Thick and Wide 15.2 Inch / 38.1cm Inside Circumference (total length)
New high quality super elasticity rubber drive belt
21′ long x 0.20′ width x 0.02′ thick ( 544mm long x 5mm width x 0.5mm thick)
Application: Fits most all 10′ to 13′ diameter platter turntables
Can replace all 21′ to 24.5′ belts (170 to 200mm BELT), Perfect replacement or belt, specs equal or exceed original standards.
Audio Technica VM Series dual magnet cartridge, Aluminum cantilever , 0.6 mil Diamond conical needle, 1.8-2.2 grams (2.0 g standard) tracking pressure
Astatic 51-1 ASTATIC 51-2 AMI ROCKOLA JUKEBOX 33 45 78
With a specialized body and internal wiring dedicated to monaural sound reproduction, plus a large curvature radius conical stylus, the VM670SP cartridge is designed for playing 78 RPM records. Part of the 600 Series in Audio-Technica’s new VM cartridge line – a line that harks back to A-T’s early days as a manufacturer primarily of high-end phono cartridges – the VM670SP is equipped with dual magnets that are internally connected to reduce record noise and obtain a highly focused “center” sound image that stereo cartridges can’t provide. The stylus’s 3.0 mil curvature radius makes it an excellent choice for playing 78s from a wide variety of eras. Includes mounting hardware.
VM dual magnet cartridge with 3.0 mil conical stylus
Paratoroidal coils improve generating efficiency
Mono body terminating left and right channels reduces surface noise
Durable low-resonance polymer housing
Four cartridge installation screws (5 mm x 2, 10 mm x 2), two washers, two hexagon nuts
All Goldring 2000 series cartridges feature Moving Iron technology. This lends them the high levels of detail associated with more expensive moving coil designs whilst retaining the convenience of a replaceable stylus and high output associated with moving magnet types. The cartridge employs a fixed samarium cobolt magnet and high output coil combination so that a very light iron/nickel cantilever end-piece can be used instead of the much heavier permanent magnet used in conventional designs. This reduces the moving mass allowing the stylus to trace the record groove more faithfully. Because of their high output, Goldring 2000 series cartridges should be used with the standard moving magnet phono input of an integrated amplifier.
The 2200 features a bonded elliptical diamond stylus and alumite cantilever which offers higher definition and improved transient response when compared to a conventional cantilever and spherical stylus.
The Klipsch T5M Wired Earphones offer superior comfort and unparalleled acoustic quality on-the-go.
VERTIGAIN® technology helps to increase quality and clarity by up to 10% compared to other digital USB microphones. As sound waves move in a vertical direction, the wave reaches the 3 condensers without being scattered by any microphone mesh.
4 Dedicated Recording Modes
The MDRILL One will be only mic you need!
4 different polar settings offer the ultimate flexibility. Record vocals, instruments, podcasts, interviews, conference calls, streaming and much, much more!
Simply press the mode button and choose between Cardioid, Stereo, Bi-Directional or Omni-Directional patterns to find the best performance setting. So, whether you stream from home or need to record your next masterpiece, the MDRILL One Pro will help you produce studio-quality recordings – every time.
Thronmax Mdrill One Black 48khz, Fabric Travel Case, Dust-proof Protective Sleeve, Foam Windshield, Pop Filter, User Guide, 3 meters Type C braided cable, Advanced Boom Adapter, 3/8” Female, 5/8″ Male Adapter
PC/Mac, Windows 8/Windows 7/Windows Vista, Mac OS X (10.7-10.9)
Product Code: M2P-B Jet Black 96 Kit
Audio-Technica’s stringent quality and consistency standards set the AT2020 apart from other mics in its class. Its low-mass diaphragm is custom-engineered for extended frequency response and superior transient response. With rugged construction for durable performance, the microphone offers a wide dynamic range and handles high SPLs with ease. The AT2020: the new standard for affordable side-address studio condensers.
The MPM-1000U is perfect for podcasting applications or recording high-quality audio directly to a computer or digital audio workstation (DAW). The built-in driver enables plug-and-play USB performance, and its smooth frequency response will put the finishing touch on any project.
The ATR2100x-USB is a versatile content creation microphone, designed for live performance, podcasting, and voiceover use. This rugged handheld microphone offers two outputs: a USB output that connects to your computer or other device for digital recording, and an XLR output that connects to a sound system’s conventional microphone input for use in live performance.
High quality Elliptical needle made by Tonar
0.4 X 0.7 mil Diamond elliptical tip needle , 16 or 33 or 45rpm NOT for 78rpm , 1.5 – 3,0 grams tracking pressure
0.7 mil Diamond conical tip needle , 16 or 33 or 45rpm NOT for 78rpm , 1,1 – 1,5 grams tracking pressure
0.7 mil Diamond conical tip needle , 16 or 33 or 45rpm NOT for 78rpm , 3,0 – 5,0 grams tracking pressure
Orders shipped within 24 hours
Showing the single result
0.7 mil Diamond conical tip needle , 16 or 33 or 45rpm NOT for 78rpm , 3,0 grams tracking pressure