MY ACCOUNT
WISHLIST
COMPARE LIST
Hello.
Username*
Password*
Lost password?
Email*
WEIGHT: 760 Grams MATERIAL: STAINLESS STEEL LOWER DIAMETER: 70 mm HIGHER DIAMETER: 28 mm HEIGHT: 20 mm
You will receive a top quality turntable headshell that is ready to plug into most S-shaped or straight tonearms. You can be up and spinning in moments. If you have an empty round socket at the end of your tonearm this headshell will fit. It will just plug right into the round tonearm socket as you rotate the locking collar. Size : 8 mm diameter x 12 mm length Plated 4-pin contacts Four colour-coded OFC (oxygen free copper) soft leadwire with gold plated terminal Every terminal inside a color sleeve
Rubber Turntable Mat Diameter: 298mm Thickness: 3mm
Turntable Cartridge 4 Piece Connector High-End Lead Wires Set with Gold connector. twisted. Pack in PP box with foam inlay Mount on cartridge according to the color of shrink tubing: BLUE = LG (left ground) GREEN = RG (right ground) WHITE = L (left positive) RED = R (right positive) Specifications of High-End Lead Wires Sets Cable -Conductor: 7N Copper (OFC), 7-strands, Dia. 0.16mm, silver -Insulation Thickness: 0.41mm -Overall Dia.: 1.32mm -Conductor Resistance at 120 degree centigrade: 42.60Ohm/Kft Connector plug -7N Copper (OFC), AS-06 SILVER connectors, White Cable
New Highest quality turntable belt, 25.7″ Inside Circumference x 0.200″ Wide x 0.027″ Thick Turntable Belt
This is a brand new generic replacement flat rubber belt.- manufactured to meet or exceed the Original Equipment Manufacturers specifications. .046 Inch / 1.2mm Thick and Wide 15.75 Inch / 40cm Inside Circumference (total length)
New Highest quality turntable belt, 24.5″/62,23 cm Inside Circumference x 0.200″/ 0,50 cm Wide x 0.023″/ 0,058 Thick Turntable Belt
High quality Elliptical cartridge made by Grado
Audio Technica VM Series dual magnet cartridge, Aluminum cantilever , 0.3 x 0.7 mil Diamond elliptical needle, 1.8-2.2 grams (2.0 g standard) tracking pressure
All Goldring 2000 series cartridges feature Moving Iron technology. This lends them the high levels of detail associated with more expensive moving coil designs whilst retaining the convenience of a replaceable stylus and high output associated with moving magnet types. The cartridge employs a fixed samarium cobolt magnet and high output coil combination so that a very light iron/nickel cantilever end-piece can be used instead of the much heavier permanent magnet used in conventional designs. This reduces the moving mass allowing the stylus to trace the record groove more faithfully. Because of their high output, Goldring 2000 series cartridges should be used with the standard moving magnet phono input of an integrated amplifier.
Increased resolution is gained for this cartridge by the use of a low-mass, “Vital” shank, nude diamond stylus and tapered aluminum cantilever. This polyhedral, line-contact profile was chosen because it has a very low tip-mass and a large contact area whilst being very narrow from front to back, enabling the accurate retrieval of even the highest frequencies in the recording. The stiff aluminium cantilever resists the establishment of unwanted resonances which are unable to propagate towards the generator due to its tapered shape. The 2400 has a low-resonance aluminium body providing a rigid connection to the tonearm, which improves bass power and clarity .
The Nagaoka MP-300 MM phonograph cartridge offers sophistication, refinement and high-definition at all audible frequencies thus making it one of our favorite phonograph cartridges. It is nimble on the grooves and easy on the ears so you keep on wanting to listen. The Nagaoka MP300 is an advanced technology cartridge that is destined to become a classic out of the box.
Features: Exclusive super rigid body for ultra resonance and superb fidelity Superfine polished special elliptical bonded diamond stylus Powerful samarium cobalt magnet Hardened low-mass, high strength boron cantilever Carbon fibre reinforced plastic body
Specifications: Type: Moving magnet Cantilever: High-strength Boron Stylus type: Superfine elliptical diamond with 0.4 x 0.7 mil Cartridge weight: 8 g Head shell’s weight: 13.5 g Output voltage @ 1kHz,5cm/sec: 3mV Frequency response: 20Hz-25kHz Channel balance @ 1kHz: > 1dB Channel separation @ 1kHz: > 25dB Recommended loading: 47k ohms Dynamic compliance: 7.2 x 10-6 cm/dyne Static compliance: 20 x 10-6 cm/dyne Tracking force range: 1.3 – 1.8 g Stylus replacement: Nagaoka JN-P300
The ATH-SR6BTBK Wireless Over-Ear Headphones let you enjoy amazing, high-fidelity audio whether you choose to listen over a traditional wired connected or via Bluetooth wireless technology. The headphones are compatible with Qualcomm aptX, AAC and SBC codecs, and connect easily with smartphones, tablets, music players, and other devices. Adding devices in the headphones’ memory is made even easier with NFC (Near Field Communication) functionality, which enables touch pairing and connection with any compatible device.
The ATH-SR6BTBK features powerful 45 mm drivers that are capable of reproducing Hi-Res Audio (5–40,000 Hz frequency response) when used with the included 1.2 m (3.9′) cable. The cable is equipped with mic and controls so it can also be used to operate devices in areas where Bluetooth wireless technology is prohibited or when headphone battery power is low. For wireless use, the headphones have a mic and volume/control switch built into the left earcup, making it easy to answer calls, adjust volume and handle music and video playback (play, pause, fast-forward, reverse, next/previous track).
DesignClosed-back dynamic
Touch Control✓
Driver Diameter45 mm
Frequency Response15 – 28,000 Hz
Battery LifeApprox. 40 hours continuous use
Charging TimeApprox. 7 hours (for 0-100% charge)
MicrophoneOmnidirectional condenser
Communication SystemBluetooth Version 5.0
Support CodecaptX, AAC, SBC
The ATH-WS990BT wireless over-ear headphones combine exclusive 53 mm Deep Motion Drivers with large, high-flux magnetic circuitry and Bluetooth technology to deliver vibrant full-range wireless audio with invigorating bass. The powerful magnetic force of the circuitry results in dynamic, well-tailored diaphragm response to reproduce deep, clear low frequencies and detailed mid-to-high frequencies.
Ideal for podcasting, home studio recording, field recording, and voiceover use, the ATR2500x-USB plugs into your computer or other device, and functions seamlessly with your favorite recording software. This large-diaphragm, side-address cardioid condenser reduces pickup of unwanted sounds from the sides and rear, and is equipped with a high-quality analog-to-digital converter (24-bit, up to 192 kHz) for excellent fidelity.
The ATR2100x-USB is a versatile content creation microphone, designed for live performance, podcasting, and voiceover use. This rugged handheld microphone offers two outputs: a USB output that connects to your computer or other device for digital recording, and an XLR output that connects to a sound system’s conventional microphone input for use in live performance.
The motiv mv88+ video kit is a premium digital stereo condenser microphone. Your new mobile recording rig directly connects to any apple device via a lightning connector, or via usb-c to select additional devices. The mv88+ has all you need to capture great content right out of the box. The included phone mount is also compatible with your existing set-up, allowing to connect to any standard ¼” tripod. The mv88+ is compatible with: Ios devices, samsung galaxy note 8, samsung galaxy note 9, samsung galaxy s7 (requires additional micro-b cable or otg adapter), samsung galaxy s8/ s8+, samsung galaxy s9/ s9+. Note that not all android devices provide enough power or support usb audio. Note that the mv88+ is not compatible with ipad pro.
The MPM-1000U is perfect for podcasting applications or recording high-quality audio directly to a computer or digital audio workstation (DAW). The built-in driver enables plug-and-play USB performance, and its smooth frequency response will put the finishing touch on any project.
High quality Conical needle made by Tonar
0.7 mil Diamond conical tip needle , 16 or 33 or 45rpm NOT for 78rpm , 1.5 – 2.5 grams tracking pressure
0.7 mil Diamond conical tip needle , 16 or 33 or 45rpm NOT for 78rpm , 1,5- 2,5 grams tracking pressure
0.2 X 0.7 mil Diamond Elliptical tip needle , 16 or 33 or 45rpm NOT for 78rpm , 1,0 – 3,0 grams tracking pressure
Orders shipped within 24 hours
0.7 mil Diamond conical tip needle ,for 78rpm , 3,0 – 5.0 grams tracking pressure
$ 32.95
0.7 mil Diamond conical tip needle , 3,0 – 5.0 grams tracking pressure
Normarh, Pfansthiel
Red
78 RPM
Conical
3,0 – 5.0 grams
no
691-D2
There are no reviews yet.
Your email address will not be published. Required fields are marked *
Your review *
Name *
Email *
0.3 X 0.7 mil Diamond Elliptical tip needle , 16 or 33 or 45rpm NOT for 78rpm , 3,0 – 5,0 grams tracking pressure
Audio-Technica ATN91 stylus specified for AT91 cartridges, Special conical diamond tip for good fidelity ,0.6 mil Diamond Conical needle , 1.5 – 2.5 grams tracking pressure
Replacement JNP200 stylus with spherical tip and aluminium alloy cantilever. Stylus: 0.4 x 0.7 Mil naked elliptical block diamond stylus tip
Audio-Technica ATN-91R stylus specified forAT91R and CN5625AL cartridges, Special conical diamond tip for good fidelity ,06 Diamond conical Replacement Stylus with Bonded Round Shank , 2 – 4 grams tracking pressure
Reviews
There are no reviews yet.